Aeroelastic behaviour of composite wings

Doctoral thesis English OPEN
Georghiades, G.A.
  • Subject: TA

This research work presents series of investigations into the structural, dynamic and aeroelastic behaviour of composite wings. The study begins with a literature review where the development of aeroelastic tailoring and specific applications of the technology are discussed in detail. A critique of methods for the determination of cross-sectional rigidity properties follows for beams constructed of laminated and thin-walled materials. Chordwise stiffness is shown to be an important parameter that must be considered as it has a significant effect on the amount of bending-torsion coupling present in a beam and, as a consequence, on the value of torsional rigidity. The free vibration characteristics of such beams are then examined using the dynamic stiffness matrix method. Natural frequencies and mode shapes of various beams are studied using the fibre angle, (3, and the bending-torsion coupling which is measured (in this study) by the non-dimensional parameter 'If, as design variables. The results show that 'If has only a marginal effect on the natural frequencies of composite beams (wings) but can significantly modify the mode shapes of such beams. It can be used to decouple modes which are geometrically (inertially) coupled in the same way as mass balancing but without a weight penalty. It can also be used to abate the unfavourable coupling introduced by sweep angle. Classical flutter and divergence of swept and unswept uniform cantilever wings are investigated using laminated flat beams (plates) and thin-walled beams of rectangular and biconvex cross-sections. Various parameters, such as, the fibre angle, (3, the coupling parameter, 'If, the angle of sweep, A, the static unbalance, xu, and the non-dimensional ratio of the fundamental (uncoupled) bending to fundamental torsional frequency, ffih/ffiu, are varied and their subsequent effects on aeroelastic stability are investigated. The importance of torsional rigidity GJ on the flutter of composite wings is shown to be substantial in contrast with 'If, which is generally the most important parameter to be considered when the objective is that of increasing the divergence speed. Modal interchanges in the free vibration and flutter of laminated composite wings are shown to be primarily responsible for behaviour not experienced with metallic wings, in particular the effect of wash-in and wash-out on flutter. The most intriguing features of these investigations, however, are those which show that models adequate for the analysis of composite wings may be based on two parameters, the frequency ratio ffih/ffiu and the coupling parameter If/. Some results are confirmed by independent optimisation studies. Finally, a preliminary investigation is carried out into the flutter suppression and gust alleviation of a laminated composite wing by the use of active controls. The results show that by using an active control in an optimum trailing edge position the gust response of a wing can be significantly alleviated without compromising the already optimised flutter speed by the use of aeroelastic tailoring
  • References (75)
    75 references, page 1 of 8

    1.29 Wallace, M. M., and Bert, C. W., "Transfer Matrix Analysis of Dynamic Response of Composite-Material Structural Elements with Material Damping," Shock and Vibration Bulletin 50, Part 3, Sept. 1980.

    1.30 Hodges, D. H., and Dowell, E. H., "Nonlinear Equations of Motion for the Elastic Bending and Torsion of Twisted Nonuniform Blades," NASA TN D-7818, 1974.

    1.31 Panda, B., and Chopra, I., "Dynamics of Composite Rotor Blades in Forward Flight," Vertica, Vol. 11, (1/2), 1987.

    1.32 Banerjee, J. R., and Williams, F. W., "Coupled Bending-Torsional Dynamic Stiffness Matrix of an Axially Loaded Timoshenko Beam Element," International Journal of Solids and Structures, Vol. 31, 1994, pp. 749-762.

    1.33 Nissim, E., "Flutter Suppression Using Active Controls Based on the Concept of Aerodynamic Energy," NASA TN D-6199, Sept. 1971.

    1.34 Nissim, E., Caspi, A., and Lottati, I., "Application of the Aerodynamic Energy Concept to Flutter Suppression and Gust Alleviation by Use of Active Controls, NASA TN D8212, June 1976.

    1.35 Suzuki, S., and Yonezawa, S., "Simultaneous Structure/Control Design Optimization of a Wing Structure with a Gust Alleviation System," Journal of Aircraft, Vol. 30, 1993, pp. 268-274.

    1.36 Layton, J. B., "Aeroservoelastic Tailoring for Gust Response of a Typical Section Aeroelastic Model," Proceedings of the 36th AIAAI SMEI ASEC/ AHS / ASC Structures, Structural Dynamics, and Materials Conference, AIM Paper 95-1192, 1995, pp. 306-313.

    1.37 Banerjee, J. R., and William, F. W., "Vibration of Composite Beams - An Exact Method Using Symbolic Computation," Journal of Aircraft, Vol. 32., 1995, pp. 636-642.

    1.38 Wittrick, W. H., and Williams, F. W., "A General Algorithm for Computing Natural Frequencies of Elastic Structures," Quarterly Journal of Mechanics and Applied Mathematics, Vol. 24, 1971, pp. 263-284.

  • Metrics
    0
    views in OpenAIRE
    0
    views in local repository
    108
    downloads in local repository

    The information is available from the following content providers:

    From Number Of Views Number Of Downloads
    City Research Online - IRUS-UK 0 108
Share - Bookmark